To determine the current mobile reception performance for good data transmission, different reception values are relevant depending on the mobile network:
2G mobile network (GPRS / EDGE)
3G mobile network (UMTS / HSPA / HSPA+)
4G mobile network (LTE)

Please note the following:

• The values, colour gradations and comments listed in the tables are empirical values for determining the current reception performance and the possible effects on data transmission. However, the real data transmission may deviate in practical use.
• Data transmission in the mobile network depends not only on mobile reception but also on other factors SIM card tariff, network availability, network load, interference, etc.

2G mobile network (GPRS / EDGE)

Data transmission in the 2G mobile network depends on the current signal strength (RSSI). The current signal strength can be read out in the cellular router, see e.g:

RSSI (Signal strength)

The 'Received Signal Strength Indicator' (RSSI) shows the current signal strength.

RSSI	Data transmission
	Very good reception with optimal data transmission
	Good data transmission without serious dropouts or interference.
	Data transmission is possible with restrictions (low bandwidth). 1
	Disturbed data transmission with dropouts, aborts and long packet transit times. 1
	No connection establishment and no data transmission possible any more. 1

¹ Stable data transmission with high bandwidths is not possible. Reception should be improved:

• When used inside buildings, radio waves are absorbed and reflected. The antennas should therefore be placed as close as possible to a window facing the transmitter mast.
• Antennas should always be placed as high as possible and ideally free-standing.
• Magnetic base antennas have a better effect if they are fixed to a metal surface (e.g. radiator, metal cabinet, etc.).
• In isolated rooms and in locations with very weak reception levels, an outdoor antenna should be used.
• Cellular routers usually have 2 antenna connections (MAIN & AUX, ANT & DIV, etc.). Especially in mobile use (e.g. in vehicles), both mobile radio antennas should be connected.

---

3G mobile network (UMTS / HSPA / HSPA+)

Data transmission in the 3G mobile network depends on the current signal strength (RSSI). The current signal strength can be read out in the cellular router, see e.g:

RSSI (Signal strength)

The 'Received Signal Strength Indicator' (RSSI) shows the current signal strength.

RSSI	Data transmission
	Very good reception with optimal data transmission
	Good data transmission without serious dropouts or interference.
	Data transmission is possible with restrictions (low bandwidth). 1
	Disturbed data transmission with dropouts, aborts and long packet transit times. 1
	No connection establishment and no data transmission possible any more. 1

¹ Stable data transmission with high bandwidths is not possible. Reception should be improved:

• When used inside buildings, radio waves are absorbed and reflected. The antennas should therefore be placed as close as possible to a window facing the transmitter mast.
• Antennas should always be placed as high as possible and ideally free-standing.
• Magnetic base antennas have a better effect if they are fixed to a metal surface (e.g. radiator, metal cabinet, etc.).
• In isolated rooms and in locations with very weak reception levels, an outdoor antenna should be used.
• Cellular routers usually have 2 antenna connections (MAIN & AUX, ANT & DIV, etc.). Especially in mobile use (e.g. in vehicles), both mobile radio antennas should be connected.

---

4G mobile network (LTE)

The current LTE reception value (RSRP) and LTE signal quality (RSRQ) are relevant for data transmission in the 4G mobile network. These reception values can be read out in the cellular router during an LTE connection, see e.g:

RSRP

'Reference Signal Received Power' (RSRP) indicates the current LTE received power value. The determined value is used to select the mobile radio cell and, in mobile use, to hand over to the next radio cell.

RSRP	Data transmission
	Data transmission is interference-free.
	Data transmission is interference-free.
	Data transmission may have slight limitations.
	Data transmission may have slight limitations.
	Data transmission with limited data throughput, dropouts and aborts are also not excluded. 1
	Data transmission with limited data throughput, dropouts and aborts are also not excluded. 1
	Disturbed data transmission with dropouts, aborts and long packet delays. 1
	Disturbed data transmission with dropouts, aborts and long packet delays. 1
	Good data transmission with almost no interference.
	Good data transmission with almost no interference.
	No connection and no data transmission possible. 1

¹ Stable data transmission with high bandwidths is not possible. Reception should be improved:

• When used inside buildings, radio waves are absorbed and reflected. The antennas should therefore be placed as close as possible to a window facing the transmitter mast.
• Antennas should always be placed as high as possible and ideally free-standing.
• Magnetic base antennas have a better effect if they are fixed to a metal surface (e.g. radiator, metal cabinet, etc.).
• In isolated rooms and in locations with very weak reception levels, an outdoor antenna should be used.
• Cellular routers usually have 2 antenna connections (MAIN & AUX, ANT & DIV, etc.). Especially in mobile use (e.g. in vehicles), both mobile radio antennas should be connected.

RSRQ

'Reference Signal Received Quality' (RSRQ) indicates the LTE signal quality.

RSRQ	Data Transmission
	Very good, no interference
	No interference with data transmission expected.
	Only slight influence on data transmission.
	Interference may affect data transmission. 2
	Noticeable influence on data transmission. 2
	Data transmission is severely disturbed and unstable. 2
	Data transmission is no longer possible. 2

² Signal quality should be improved:

• Use in isolated rooms, e.g. in metal cabinets or in metal halls, causes reflections and should be avoided.
• Do not place the antennas in the immediate vicinity of other sources of interference (machines, radio transmitters, etc.).
• Use a remote outdoor antenna in a location with less interference.
• If there are other radio transmitters in the immediate vicinity, however, outdoor antennas with high reception power could have a negative effect on the signal quality. An overview of nearby radio transmitters can be found in the EMF database of the Federal Network Agency.

RSSI (Signal strength)

The 'Received Signal Strength Indicator' (RSSI) shows the current signal strength, which, however, has no significance for data transmission with an LTE connection.